Rear Passenger Side Brake Caliper - ACDelco (18FR2172)
- 18fr2172
Details
- Brand:
- SKU:
18FR2172
- GTIN: 00707773269718
- UPC: 707773269718
- Positions: Rear Right
- Other Names:
19165298
- Description: ACDelco Gold (Professional) Remanufactured Friction Ready Disc Brake Calipers are the high quality alternative to Original Equipment (OE) parts. They use both aluminum and iron castings. These loaded calipers contain Ethylene Propylene (EPDM) rubber components to provide superior resistance to heat, corrosion, and leakage. ACDelco Professional Remanufactured Friction Ready Disc Brake Calipers are developed without attached brake pads, allowing customization for the application at hand. Bleeder screws, copper sealing washers, hardware, and mounting brackets are all included for easy installation. Remanufacturing disc brake calipers is an automotive industry practice that involves disassembly of existing units, and replacing components that are most prone to wear with new components. Damaged and obsolete parts are replaced and are end of line tested to ensure they perform to ACDelco specifications. In addition, remanufacturing returns components back into service rather than processing as scrap or simply disposing of them. ⚠ WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
disc-brake-caliper;caliper;brake-caliper;disc-brake; - Condition: New
California Proposition 65
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov Additional Information
| Brand | ACDelco Gold |
| Abutment Clips Included | Yes |
| Anti-Rattle Spring Included | No |
| Bleeder Thread Diameter | M10x1 |
| Caliper Color | Natural |
| Caliper Piston Quantity | 2 |
| Caliper Slides Included | Yes |
| Caliper Type | Floating |
| Casting Material | Cast Iron |
| Disc Brake Caliper Casting Material | Cast Iron |
| FAQ - Answer 1 | No, but it is a good idea to inspect them for wear-out, cracking, leaking etc. |
| FAQ - Answer 2 | Yes, ACDelco also offers GM OE disc brake calipers. |
| FAQ - Answer 3 | No, but it is a good idea to inspect them at every tire rotation. |
| FAQ - Question 1 | Do I have to replace all my brake parts when replacing my disc brake calipers? |
| FAQ - Question 2 | Does ACDelco offer other grades of disc brake calipers? |
| FAQ - Question 3 | Do I have to replace my disc brake calipers after a certain amount of time? |
| Features & Benefits - Bullet 1 | Pressure tested to ensure safe and confident braking |
| Features & Benefits - Bullet 2 | Cast iron and aluminum specifications; no extra stress on the brake boosting mounting |
| Features & Benefits - Bullet 3 | Developed without attached brake pads for customization |
| Finish | Plain |
| Good Maintenance Practices - Section 1 - Bullet 1 | Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations. |
| Good Maintenance Practices - Section 1 - Bullet 2 | Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required. |
| Good Maintenance Practices - Section 1 - Bullet 3 | Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary). |
| Good Maintenance Practices - Section 1 - Bullet 4 | Check the thickness of your brake pads. |
| Good Maintenance Practices - Section 1 - Header | The following inspections and maintenance procedures can help prevent potential brake problems: |
| Good Maintenance Practices - Section 2 - Bullet 1 | Inspection of the brake hoses for brittleness or cracking. |
| Good Maintenance Practices - Section 2 - Bullet 2 | Inspection of brake lining and pads for wear or contamination by brake fluid or grease. |
| Good Maintenance Practices - Section 2 - Bullet 3 | Inspection of wheel bearings and grease seals. |
| Good Maintenance Practices - Section 2 - Bullet 4 | Parking brake adjustments (as needed). |
| Good Maintenance Practices - Section 2 - Header | The following should be conducted by a qualified technician: |
| Grade Type | Performance |
| Height (in) | 6.5 |
| Inlet Fitting Type | Female |
| Length (in) | 13.8 |
| Mounting Bolt Thread Pitch (mm) | 2.000 |
| Mounting Bracket Included | Yes |
| Mounting Hardware Included | Yes |
| Mounting Hole Diameter | 14 |
| PADB ID 2223 | 0.394 10 |
| Pad Wear Sensor Included | No |
| Pads Included | No |
| Piston 1 Diameter (in) | 2 |
| Piston 1 Diameter (mm) | 50.8 |
| Piston 2 Diameter (in) | 2 |
| Piston 2 Diameter (mm) | 50.8 |
| Piston Quantity | 2 |
| Programming Required | No |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 1 | Vehicle pulls to the left or right when brakes are applied. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 2 | Brake pedal pulsation (not to be confused with normal ABS operation). |
| Weight (lb) | 15.26 |
| Width (in) | 7.1 |
Vehicle Fitment
| Year | Make | Model | Body & Trim | Engine & Transmission |
|---|
Interchange
Policies
FindVintageParts.com
Welcome to FindVintageParts.com — your trusted source for hard-to-find Genuine OEM automotive parts. With over 30 years of experience in the automotive industry, we have built a reputation as the go-to destination for Genuine OEM parts from leading manufacturers, including Ford, BMW, General Motors, Honda, Mazda, Mercedes-Benz, Mopar, and Toyota.
Every part we sell is brand new and delivered in the manufacturer’s original packaging — the very same components installed at the factory. To ensure complete confidence in your purchase, we offer a free compatibility guarantee with the submission of your VIN, helping you get the right part the first time.
Our team of experienced parts professionals are always ready to assist by phone, text, or email. Whether you have questions about fitment, availability, or product details, we are here to provide expert guidance every step of the way.
For answers to common questions regarding returns, shipping, order tracking, or compatibility, please visit our FAQ page.
At FindVintageParts.com, we take pride in delivering Genuine OEM parts with unmatched service and support, helping you keep your vehicle running just as the manufacturer intended.